ASTM - List of Popular Standards:-
ANNUAL BOOK OF ASTM STANDARDS - SUBJECT INDEX; ALPHANUMERIC LIST,
ASTM C 581
Standard Practice for Determining Chemical Resistance of Thermosetting
Resins Used in Glass-Fiber-Reinforced Structures Intended for Liquid Service
Standard Specification for Contact-Molded Reinforced Thermosetting Plastic
(RTP) Laminates for Corrosion-Resistant Equipment
Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and
Sheeting
Standard Test Method for Linear Dimensional Changes of plastic under
Accelerated Service Conditions
Standard Test Method for Stiffness Properties of plastic as a Function of
Temperature by Means of a Torsion Test
Standard Test Method for Resistance of Transparent plastic to Surface
Abrasion
Standard Test Methods for Sampling and Testing Plasticizers Used in plastic
Standard Specifications for Flexible Cellular Materials - Latex Foam
Standard Specification for Flexible Cellular Materials - Sponge or Expanded
Rubber
Standard Specification for Thermosetting Polyester Molding Compounds
Standard Test Methods for Volatile Loss from plastic Using Activated Carbon
Methods
Standard Test Method for Linear Dimensional Changes of Nonrigid
Thermoplastic Sheeting or Film at Elevated Temperature
Standard Test Method for Melt Flow Rates of Thermoplastic by Extrusion
Plastometer
Standard Test Method for Resistance of Plastic Films to Extraction by
Chemicals
Standard Test Method for Dilute Solution Viscosity of Vinyl Chloride
Polymers
Standard Specification for Polyethylene plastic Extrusion Materials for
Wire and Cable
Standard Specification for Octyl Ortho-Phthalate Ester Plasticizers
Standard Classification System for Polychlorotrifluoroethylene (PCTFE)
plastic
Standard Practice for Outdoor Weathering of plastic
Standard Test Method for Diffuse Light Transmission Factor of Reinforced
plastic Panels
Standard Practice for Filtered Open-Flame Carbon-Arc Exposures of plastic
Standard Test Method for Density of plastic by the Density-Gradient
Technique
Standard Test Method for Vicat Softening Temperature of plastic
Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic
Pipe, Schedules 40 and 80
Standard Specification for Cellulose Acetate Propionate Molding and
Extrusion Compounds
Standard Specification for Nonrigid Vinyl Chloride Plastic Film and Sheeting
Standard Test Method for Time-To-Failure of Plastic Pipe under Constant
Internal Pressure
Standard Test Method for Resistance to Short-Time Hydraulic Pressure of
Plastic Pipe, Tubing, and Fittings
Standard Terminology for Abbreviated Terms Relating to plastic
Standard Test Method for Dilute Solution Viscosity of Ethylene Polymers
Standard Test Method for Compressive Properties Of Rigid Cellular plastic
Standard Test Method for Apparent Density of Rigid Cellular plastic
Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid
Cellular plastic
Standard Specification for Allyl Molding Compounds
Standard Specification for Flexible Cellular MaterialsPoly (Vinyl Chloride)
Foam (Closed-Cell)
Standard Test Method for Environmental Stress-Cracking of Ethylene plastic
Standard Test Method for Tensile Properties of plastic by Use of
Microtensile Specimens
Standard Test Methods for Impact Resistance of Plastic Film by the Free-
Falling Dart Method
Standard Specification for Extruded and Compression Molded
Polytetrafluoroethylene (PTFE) Rod and Heavy Walled Tubing
Standard Practice for Resistance of plastic to Sulfide Staining
Standard Test Method for Transparency of Plastic Sheeting
Standard Specification for Poly(Vinyl Chloride) Resins
Standard Specification for Epoxy Resins
Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and
Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds
Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe,
Schedules 40, 80, and 120
ASTM D 1786
Standard Specification for Toluene Diisocyanate
ASTM D 1790
Standard Test Method for Brittleness Temperature of Plastic Sheeting by
Impact
ASTM D 1822
Standard Test Method for Tensile-Impact Energy to Break plastic and
Electrical Insulating Materials
ASTM D 1823
Standard Test Method for Apparent Viscosity of Plastisols and Organosols at
High Shear Rates by Extrusion Viscometer
ASTM D 1824
Standard Test Method for Apparent Viscosity of Plastisols and Organosols at
Low Shear Rates
ASTM D 1894
Standard Test Method for Static and Kinetic Coefficients of Friction of
Plastic Film and Sheeting
ASTM D 1895
Standard Test Methods for Apparent Density, Bulk Factor, and Pourability of
Plastic Materials
ASTM D 1896
Standard Practice for Transfer Molding Test Specimens of Thermosetting
Compounds
ASTM D 1921
Standard Test Methods for Particle Size (Sieve Analysis) of Plastic
Materials
ASTM D 1922
Standard Test Method for Propagation Tear Resistance of Plastic Film and
Thin Sheeting by Pendulum Method
ASTM D 1929
Standard Test Method for Determining Ignition Temperature of plastic
ASTM D 1938
Standard Test Method for Tear-Propagation Resistance (Trouser Tear) of
Plastic Film and Thin Sheeting by a Single-Tear Method
ASTM D 1972
Standard Practice for Generic Marking of Plastic Products
ASTM D 1996
Standard Test Method for Determination of Phenolic Antioxidants and
Erucamide Slip Additives in Low Density Polyethylene Using Liquid
Chromatography (LC)
ASTM D 1998
Standard Specification for Polyethylene Upright Storage Tanks
ASTM D 2103
Standard Specification for Polyethylene Film and Sheeting
ASTM D 2104
Standard Specification for Polyethylene (PE) Plastic Pipe, Schedule 40
ASTM D 2105
Standard Test Method for Longitudinal Tensile Properties of "Fiberglass"
(Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Tube
ASTM D 2115
Standard Practice for Oven Heat Stability of Poly(Vinyl Chloride)
Compositions
ASTM D 2116
Standard Specification for FEP-Fluorocarbon Molding and Extrusion Materials
ASTM D 2122
Standard Test Method for Determining Dimensions of Thermoplastic Pipe and
Fittings
ASTM D 2124
Standard Test Method for Analysis of Components in Poly(Vinyl Chloride)
Compounds Using an Infrared Spectrophotometric Technique
ASTM D 2126
Standard Test Method for Response of Rigid Cellular plastic to Thermal and
Humid Aging
ASTM D 2143
Standard Test Method for Cyclic Pressure Strength of Reinforced,
Thermosetting Plastic Pipe
ASTM D 2152
Standard Test Method for Adequacy of Fusion of Extruded Poly(Vinyl Chloride)
(PVC) Pipe and Molded Fittings by Acetone Immersion
ASTM D 2222
Standard Test Method for Methanol Extract of Vinyl Chloride Resins
ASTM D 2235
Standard Specification for Solvent Cement for
Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings
ASTM D 2238
Standard Test Methods for Absorbance of Polyethylene Due to Methyl Groups at
1378 cm-1
ASTM D 2239
Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on
Controlled Inside Diameter
ASTM D 2241
Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe
(SDR Series)
ASTM D 2282
Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic
Pipe (SDR-PR)
ASTM D 2287
Standard Specification for Nonrigid Vinyl Chloride Polymer and Copolymer
Molding and Extrusion Compounds
ASTM D 2288
Standard Test Method for Weight Loss of Plasticizers on Heating
ASTM D 2290
Standard Test Method for Apparent Hoop Tensile Strength of Plastic or
Reinforced Plastic Pipe by Split Disk Method
ASTM D 2291
Standard Practice for Fabrication of Ring Test Specimens for Glass-Resin
Composites
ASTM D 2310
Standard Classification for Machine-Made "Fiberglass" (Glass-Fiber-
Reinforced Thermosetting-Resin) Pipe
ASTM D 2321
Standard Practice for Underground Installation of Thermoplastic Pipe for
Sewers and Other Gravity-Flow Applications
ASTM D 2343
Standard Test Method for Tensile Properties of Glass Fiber Strands, Yarns,
and Rovings Used in Reinforced plastic
ASTM D 2383
Standard Practice for Testing Plasticizer Compatibility in Poly(Vinyl
Chloride) (PVC) Compounds under Humid Conditions
ASTM D 2396
Standard Test Methods for Powder-Mix Time of Poly(Vinyl Chloride) (PVC)
Resins Using a Torque Rheometer
ASTM D 2412
Standard Test Method for Determination of External Loading Characteristics
of Plastic Pipe by Parallel-Plate Loading
ASTM D 2444
Standard Test Method for Determination of the Impact Resistance of
Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
ASTM D 2447
Standard Specification for Polyethylene (PE) Plastic Pipe, Schedules 40 and
80, Based on Outside Diameter
ASTM D 2457
Standard Test Method for Specular Gloss of Plastic Films and Solid plastic
ASTM D 2463
Standard Test Method for Drop Impact Resistance of Blow-Molded Thermoplastic
Containers
ASTM D 2464
Standard Specification for Threaded Poly(Vinyl Chloride) (PVC) Plastic Pipe
Fittings, Schedule 80
ASTM D 2466
Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings,
Schedule 40
ASTM D 2467
Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings,
Schedule 80
ASTM D 2471
Standard Test Method for Gel Time and Peak Exothermic Temperature of
Reacting Thermosetting Resins
ASTM D 2513
Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and
Fittings
ASTM D 2517
Standard Specification for Reinforced Epoxy Resin Gas Pressure Pipe and
Fittings
ASTM D 2538
Standard Practice for Fusion of Poly(Vinyl Chloride) (PVC) Compounds Using a
Torque Rheometer
ASTM D 256 REV A
Standard Test Methods for Determining the Izod Pendulum Impact Resistance of
plastic
ASTM D 2561
Standard Test Method for Environmental Stress-Crack Resistance of Blow-
Molded Polyethylene Containers
ASTM D 2562
Standard Practice for Classifying Visual Defects in Parts Molded from
Reinforced Thermosetting plastic
ASTM D 2563
Standard Practice for Classifying Visual Defects in Glass-Reinforced Plastic
Laminate Parts
ASTM D 2564
Standard Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC)
Plastic Piping Systems
ASTM D 2565
Standard Practice for Xenon-Arc Exposure of plastic Intended for Outdoor
Applications
ASTM D 2578 REV A
Standard Test Method for Wetting Tension of Polyethylene and Polypropylene
Films
ASTM D 2581
Standard Classification System for Polybutylene (PB) plastic Molding and
Extrusion Materials
ASTM D 2582
Standard Test Method for Puncture-Propagation Tear Resistance of Plastic
Film and Thin Sheeting
ASTM D 2583
Standard Test Method for Indentation Hardness of Rigid plastic by Means of
a Barcol Impressor
ASTM D 2584
Standard Test Method for Ignition Loss of Cured Reinforced Resins
ASTM D 2609
Standard Specification for Plastic Insert Fittings for Polyethylene (PE)
Plastic Pipe
ASTM D 2647 REV A
Standard Specification for Crosslinkable Ethylene plastic
ASTM D 2657
Standard Practice for Heat Fusion Joining of Polyolefin Pipe and Fittings
ASTM D 2659
Standard Test Method for Column Crush Properties of Blown Thermoplastic
Containers
ASTM D 2661
Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40
Plastic Drain, Waste, and Vent Pipe and Fittings
ASTM D 2665 REV A
Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste,
and Vent Pipe and Fittings
ASTM D 2672 REV A
Standard Specification for Joints for IPS PVC Pipe Using Solvent Cement
ASTM D 2673
Standard Specification for Oriented Polypropylene Film
ASTM D 2680
Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) and
Poly(Vinyl Chloride) (PVC) Composite Sewer Piping
ASTM D 2683
Standard Specification for Socket-Type Polyethylene Fittings for Outside
Diameter-Controlled Polyethylene Pipe and Tubing
ASTM D 2684
Standard Test Method for Permeability of Thermoplastic Containers to
Packaged Reagents or Proprietary Products
ASTM D 2729
Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer Pipe and
Fittings
ASTM D 2732
Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic
Film and Sheeting
ASTM D 2734
Standard Test Methods for Void Content of Reinforced plastic
ASTM D 2737
Standard Specification for Polyethylene (PE) Plastic Tubing
ASTM D 2741
Standard Test Method for Susceptibility of Polyethylene Bottles to Soot
Accumulation
ASTM D 2749
Standard Symbols for Dimensions of Plastic Pipe Fittings
ASTM D 2751
Standard Specification for Acrylonitrile-Butadiene- Styrene (ABS) Sewer Pipe
and Fittings
ASTM D 2765
Standard Test Methods for Determination of Gel Content and Swell Ratio of
Crosslinked Ethylene plastic
ASTM D 2774
Standard Practice for Underground Installation of Thermoplastic Pressure
Piping
ASTM D 2837
Standard Test Method for Obtaining Hydrostatic Design Basis for
Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe
Products
ASTM D 2838
Standard Test Method for Shrink Tension and Orientation Release Stress of
Plastic Film and Thin Sheeting
ASTM D 2839
Standard Practice for Use of a Melt Index Strand for Determining Density of
Polyethylene
ASTM D 2842
Standard Test Method for Water Absorption of Rigid Cellular plastic
ASTM D 2843
Standard Test Method for Density of Smoke from the Burning or Decomposition
of plastic
ASTM D 2846/D 2846M
Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic
Hot- and Cold-Water Distribution Systems
ASTM D 2852
Standard Specification for Styrene-Rubber (SR) Plastic Drain Pipe and
Fittings
ASTM D 2855
Standard Practice for Making Solvent-Cemented Joints with Poly(Vinyl
Chloride) (PVC) Pipe and Fittings
ASTM D 2856
Standard Test Method for Open-Cell Content of Rigid Cellular plastic by the
Air Pycnometer
ASTM D 2857
Standard Practice for Dilute Solution Viscosity of Polymers
ASTM D 2863
Standard Test Method for Measuring the Minimum Oxygen Concentration to
Support Candle-like Combustion of plastic (Oxygen Index)
ASTM D 2911
Standard Specification for Dimensions and Tolerances for Plastic Bottles
ASTM D 2923
Standard Test Method for Rigidity of Polyolefin Film and Sheeting
ASTM D 2924
Standard Test Method for External Pressure Resistance of "Fiberglass"
(Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
ASTM D 2925
Standard Test Method for Beam Deflection of "Fiberglass" (Glass-Fiber-
Reinforced Thermosetting Resin) Pipe under Full Bore Flow
ASTM D 2949 REV A
Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl
Chloride)(PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
ASTM D 2951
Standard Test Method for Resistance of Types III and IV Polyethylene
plastic to Thermal Stress-Cracking
ASTM D 2990
Standard Test Methods for Tensile, Compressive, and Flexural Creep and
Creep-Rupture of plastic
ASTM D 2992
Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for
"Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings
ASTM D 2996
Standard Specification for Filament-Wound "Fiberglass" (Glass-Fiber-
Reinforced Thermosetting-Resin) Pipe
ASTM D 2997
Standard Specification for Centrifugally Cast "Fiberglass" (Glass-Fiber-
Reinforced Thermosetting-Resin) Pipe
ASTM D 3012
Standard Test Method for Thermal-Oxidative Stability of Polypropylene Using
a Specimen Rotator within an Oven
ASTM D 3013
Standard Specification for Epoxy Molding Compounds
ASTM D 3014 REV A
Standard Test Method for Flame Height, Time of Burning, and Loss of Mass of
Rigid Thermoset Cellular plastic in a Vertical Position
ASTM D 3016
Standard Practice for Use of Liquid Exclusion Chromatography Terms and
Relationships
ASTM D 3030
Standard Test Method for Volatile Matter (Including Water) of Vinyl Chloride
Resins
ASTM D 3034 REV A
Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe
and Fittings
ASTM D 3035 REV A
Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on
Controlled Outside Diameter
ASTM D 3045
Standard Practice for Heat Aging of plastic without Load
ASTM D 3122
Standard Specification for Solvent Cements for Styrene-Rubber (SR) Plastic
Pipe and Fittings
ASTM D 3123
Standard Test Method for Spiral Flow of Low-Pressure Thermosetting Molding
Compounds
ASTM D 3124
Standard Test Method for Vinylidene Unsaturation in Polyethylene by Infrared
Spectrophotometry
ASTM D 3138
Standard Specification for Solvent Cements for Transition Joints Between
Acrylonitrile- Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC)
Non-Pressure Piping Components
ASTM D 3139
Standard Specification for Joints for Plastic Pressure Pipes Using Flexible
Elastomeric Seals
ASTM D 3159
Standard Specification for Modified ETFE-Fluoropolymer Molding and Extrusion
Materials
ASTM D 3212 REV A
Standard Specification for Joints for Drain and Sewer Plastic Pipes Using
Flexible Elastomeric Seals
ASTM D 3222
Standard Specification for Unmodified Poly (Vinylidene Fluoride) (PVDF)
Molding Extrusion and Coating Materials
ASTM D 3261
Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic
Fittings for Polyethylene (PE) Plastic Pipe and Tubing
ASTM D 3262
Standard Specification for "Fiberglass" (Glass-Fiber-Reinforced
Thermosetting-Resin) Sewer Pipe
ASTM D 3275
Standard Classification System for E-CTFE-Fluoroplastic Molding, Extrusion,
and Coating Materials
ASTM D 3291
Standard Practice for Compatibility of Plasticizers in Poly(Vinyl Chloride)
plastic Under Compression
ASTM D 3294
Standard Specification for Polytetrafluoroethylene (PTFE) Resin Molded Sheet
and Molded Basic Shapes-Replaces ASTM D3293
ASTM D 3295
Standard Specification for PTFE Tubing, Miniature Beading and Spiral Cut
Tubing
ASTM D 3296
Standard Specification for FEP-Fluorocarbon Tube
ASTM D 3299
Standard Specification for Filament-Wound Glass-Fiber-Reinforced Thermoset
Resin Corrosion-Resistant Tanks
ASTM D 3307
Standard Specification for Perfluoroalkoxy (PFA)-Fluorocarbon Resin Molding
and Extrusion Materials
ASTM D 3308
Standard Specification for PTFE Resin Skived Tape
ASTM D 3309 REV A
Standard Specification for Polybutylene (PB) Plastic Hot- and Cold-Water
Distribution Systems
ASTM D 3311
Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings
Patterns
ASTM D 3350
Standard Specification for Polyethylene plastic Pipe and Fittings Materials
ASTM D 3354
Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate
Method
ASTM D 3364
Standard Test Method for Flow Rates for Poly(Vinyl Chloride) with Molecular
Structural Implications
ASTM D 3367
Standard Test Method for Plasticizer Sorption of Poly(Vinyl Chloride) Resins
Under Applied Centrifugal Force
ASTM D 3368
Standard Specification for FEP-Fluorocarbon Sheet and Film
ASTM D 3369
Standard Specification for Polytetrafluoroethylene (PTFE) Resin Cast Film
ASTM D 3417
Standard Test Method for Enthalpies of Fusion and Crystallization of
Polymers by Differential Scanning Calorimetry (DSC)
ASTM D 3418
Standard Test Method for Transition Temperatures of Polymers By Differential
Scanning Calorimetry
ASTM D 3419
Standard Practice for In-Line Screw-Injection Molding Test Specimens from
Thermosetting Compounds
ASTM D 3420
Standard Test Method for Pendulum Impact Resistance of Plastic Film
ASTM D 3453
Standard Specification for Flexible Cellular MaterialsUrethane for Furniture
and Automotive Cushioning, Bedding, and Similar Applications
ASTM D 3465
Standard Test Method for Purity of Monomeric Plasticizers by Gas
Chromatography
ASTM D 3489
Standard Test Methods for Rubber - Microcellular Urethane
ASTM D 3517
Standard Specification for "Fiberglass" (Glass-Fiber-Reinforced
Thermosetting-Resin) Pressure Pipe
ASTM D 3567
Standard Practice for Determining Dimensions of Fiberglass (Glass-Fiber-
Reinforced Thermosetting Resin) Pipe and Fittings
ASTM D 3574
Standard Test Methods for Flexible Cellular MaterialsSlab, Bonded, and
Molded Urethane Foams
ASTM D 3575
Standard Test Methods for Flexible Cellular Materials Made from Olefin
Polymers
ASTM D 3576
Standard Test Method for Cell Size of Rigid Cellular plastic
ASTM D 3591
Standard Test Method for Determining Logarithmic Viscosity Number of
Poly(Vinyl Chloride) (PVC) in Formulated Compounds
ASTM D 3594
Standard Test Method for Copolymerized Ethyl Acrylate in Ethylene-Ethyl
Acrylate Copolymers
ASTM D 3595
Standard Specification for Polychlorotrifluoroethylene (PCTFE) Extruded
Plastic Sheet and Film
ASTM D 3641
Standard Practice for Injection Molding Test Specimens of Thermoplastic
Molding and Extrusion Materials
ASTM D 3647
Standard Practice for Classifying Reinforced Plastic Pultruded Shapes
According to Composition
ASTM D 3675
Standard Test Method for Surface Flammability of Flexible Cellular Materials
Using a Radiant Heat Energy Source
ASTM D 3676
Standard Specification for Rubber Cellular Cushion Used for Carpet or Rug
Underlay
ASTM D 3678
Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Interior-Profile
Extrusions
ASTM D 3679
Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding
ASTM D 3681
Standard Test Method for Chemical Resistance of "Fiberglass" (Glass-Fiber-
Reinforced Thermosetting-Resin) Pipe in a Deflected Condition
ASTM D 3748
Standard Practice for Evaluating High-Density Rigid Cellular plastic
ASTM D 3749
Standard Test Method for Residual Vinyl Chloride Monomer in Poly(Vinyl
Chloride) Resins by Gas Chromatographic Headspace Technique
ASTM D 3753
Standard Specification for Glass-Fiber-Reinforced Polyester Manholes and
Wetwells
ASTM D 3754
Standard Specification for "Fiberglass" (Glass-Fiber-Reinforced
Thermosetting-Resin) Sewer and Industrial Pressure Pipe
ASTM D 3763
Standard Test Method for High Speed Puncture Properties of plastic Using
Load and Displacement Sensors
ASTM D 3768
Standard Test Method for Microcellular Urethanes - Flexural Recovery
ASTM D 3769
Standard Test Method for Microcellular Urethanes - High-Temperature Sag
ASTM D 3795 REV A
Standard Test Method for Thermal Flow, Cure, and Behavior Properties of
Pourable Thermosetting Materials by Torque Rheometer
ASTM D 3801
Standard Test Method for Measuring the Comparative Burning Characteristics
of Solid plastic in a Vertical Position
ASTM D 3826
Standard Practice for Determining Degradation End Point in Degradable
Polyethylene and Polypropylene Using a Tensile Test
ASTM D 3835
Standard Test Method for Determination of Properties of Polymeric Materials
by Means of a Capillary Rheometer
ASTM D 3839
Standard Guide for Underground Installation of Fiberglass (Glass-
FiberReinforced Thermosetting-Resin) Pipe
ASTM D 3840
Standard Specification for Fiberglass (Glass-Fiber-Reinforced
Thermosetting-Resin) Pipe Fittings for Nonpressure Applications
ASTM D 3841
Standard Specification for Glass-Fiber-Reinforced Polyester Plastic Panels
ASTM D 3846
Standard Test Method for In-Plane Shear Strength of Reinforced plastic
ASTM D 3851
Standard Specification for Urethane Microcellular Shoe Soling Materials
ASTM D 3892
Standard Practice for Packaging/Packing of plastic
ASTM D 3895
Standard Test Method for Oxidative-Induction Time of Polyolefins by
Differential Scanning Calorimetry
ASTM D 3914
Standard Test Method for In-Plane Shear Strength of Pultruded Glass-
Reinforced Plastic Rod
ASTM D 3915 REV A
Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated
Poly(Vinyl Chloride) (CPVC) Compounds for Plastic Pipe and Fittings Used in
Pressure Applications
ASTM D 3916
Standard Test Method for Tensile Properties of Pultruded Glass-Fiber-
Reinforced Plastic Rod
ASTM D 3917
Standard Specification for Dimensional Tolerance of Thermosetting Glass-
Reinforced plastic Pultruded Shapes
ASTM D 3918
Standard Terminology Relating to Reinforced Plastic Pultruded Products
ASTM D 3935
Standard Specification for Polycarbonate (PC) Unfilled and Reinforced
Material
ASTM D 3965
Standard Specification for Rigid Acrylonitrile-Butadiene-Styrene (ABS)
Materials for Pipe and Fittings
ASTM D 3981
Standard Specification for Polyethylene Films Made from Medium-Density
Polyethylene for General Use and Packaging Applications
ASTM D 3982
Standard Specification for Contact Molded "Fiberglass" (Glass Fiber
Reinforced Thermosetting Resin) Duct and Hoods
ASTM D 4000
Standard Classification System for Specifying Plastic Materials
ASTM D 4001
Standard Test Method for Determination of Weight-Average Molecular Weight of
Polymers by Light Scattering
ASTM D 4020
Standard Specification for Ultra-High-Molecular-Weight Polyethylene Molding
and Extrusion Materials
ASTM D 4024
Standard Specification for Machine Made "Fiberglass" (Glass-Fiber-
Reinforced Thermosetting Resin) Flanges
ASTM D 4065
Standard Practice for plastic: Dynamic Mechanical Properties: Determination
and Report of Procedures
ASTM D 4066 REV A
Standard Classification System for Nylon Injection and Extrusion Materials
(PA)
ASTM D 4067
Standard Classification System for Reinforced and Filled Poly(Phenylene
Sulfide) (PPS) Injection Molding and Extrusion Materials Using ASTM Methods
ASTM D 4068
Standard Specification for Chlorinated Polyethylene (CPE) Sheeting for
Concealed Water-Containment Membrane
ASTM D 4092
Standard Terminology:plastic: Dynamic Mechanical Properties
ASTM D 4093
Standard Test Method for Photoelastic Measurements of Birefringence and
Residual Strains in Transparent or Translucent Plastic Materials
ASTM D 4094
Standard Test Method for Acid Content of Ethylene-Acrylic Acid Copolymers
ASTM D 4097
Standard Specification for Contact-Molded Glass-Fiber-Reinforced Thermoset
Resin Corrosion-Resistant Tanks
ASTM D 4101 REV A
Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM D 4161
Standard Specification for Fiberglass (Glass-Fiber-Reinforced
Thermosetting-Resin) Pipe Joints Using Flexible Elastomeric Seals
ASTM D 4166
Standard Test Method for Measurement of Thickness of Nonmagnetic Materials
by Means of a Digital Magnetic Intensity Instrument
ASTM D 4167
Standard Specification for Fiber-Reinforced Plastic Fans and Blowers
ASTM D 4181
Standard Classification for Acetal (POM) Molding and Extrusion Materials
ASTM D 4203
Standard Specification for Styrene-Acrylonitrile (SAN) Injection and
Extrusion Materials
ASTM D 4204
Standard Practice for Preparing Plastic Film Specimens for a Round-Robin
Study
ASTM D 4216
Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) and Related PVC
and Chlorinated Poly(Vinyl Chloride) (CPVC) Building Products Compounds
ASTM D 4218
Standard Test Method for Determination of Carbon Black Content in
Polyethylene Compounds by the Muffle-Furnace Technique
ASTM D 4225
Standard Specification for Styrene-Butadiene Sheeting
ASTM D 4226
Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride)
(PVC) Building Products
ASTM D 4272
Standard Test Method for Total Energy Impact of Plastic Films by Dart Drop
ASTM D 4273
Standard Test Method for Polyurethane Raw Materials: Determination of
Primary Hydroxyl Content of Polyether Polyols
ASTM D 4274
Standard Test Methods for Testing Polyurethane Raw Materials: Determination
of Hydroxyl Numbers of Polyols
ASTM D 4275
Standard Test Method for Determination of Butylated Hydroxy Toluene (BHT) in
Polymers of Ethylene and Ethylene Vinyl Acetate (EVA) Copolymers By Gas
Chromatography
ASTM D 4321
Standard Test Method for Package Yield of Plastic Film
ASTM D 4322
Standard Test Method for Residual Acrylonitrile Monomer
Styrene-Acrylonitrile Copolymers and Nitrile Rubber by Headspace Gas
Chromatography
ASTM D 4329
Standard Practice for Fluorescent UV Exposure of plastic
ASTM D 4349
Classification System for Polyphenylene Ether (PPE) Materials
ASTM D 4364
Standard Practice for Performing Outdoor Accelerated Weathering Tests of
plastic Using Concentrated Sunlight
ASTM D 4385
Standard Practice for Classifying Visual Defects in Thermosetting Reinforced
Plastic Pultruded Products
ASTM D 4396 REV A
Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated
Poly(Vinyl Chloride) (CPVC) Compounds for Plastic Pipe and Fittings Used in
Nonpressure Applications
ASTM D 4397
Standard Specification for Polyethylene Sheeting for Construction,
Industrial, and Agricultural Applications
ASTM D 4398
Standard Test Method for Determining the Chemical Resistance of Fiberglass-
Reinforced Thermosetting Resins by One-Side Panel Exposure
ASTM D 4440
Standard Practice for Rheological Measurement of Polymer Melts Using Dynamic
Mechanical Procedures
ASTM D 4441
Standard Specification for Aqueous Dispersions of Polytetrafluoroethylene
ASTM D 4443
Standard Test Method for Determining Residual Vinyl Chloride Monomer Content
in PPB Range in Vinyl Chloride Homo- and Co-Polymers by Headspace Gas
Chromatography
ASTM D 4459
Standard Practice for Xenon-Arc Exposure of plastic Intended for Indoor
Applications
ASTM D 4473
Standard Test Method for plastic: Dynamic Mechanical Properties: Cure
Behavior
ASTM D 4474
Standard Classification System for Styrenic Thermoplastic Elastomer
Injection Molding and Extrusion Materials (TES)
ASTM D 4475
Standard Test Method for Apparent Horizontal Shear Strength of Pultruded
Reinforced Plastic Rods By the Short-Beam Method
ASTM D 4476
Standard Test Method for Flexural Properties of Fiber Reinforced Pultruded
Plastic Rods
ASTM D 4477 REV A
Standard Specification for Rigid (Unplasticized) Poly(Vinyl Chloride) (PVC)
Soffit
ASTM D 4495
Standard Test Method for Impact Resistance of Poly(Vinyl Chloride) (PVC)
Rigid Profiles by Means of a Falling Weight
ASTM D 4508
Standard Test Method for Chip Impact Strength of plastic
ASTM D 4526
Standard Practice for Determination of Volatiles in Polymers by Static
Headspace Gas Chromatography
ASTM D 4549
Standard Specification for Polystyrene and Rubber-Modified Polystyrene
Molding and Extrusion Materials (PS)
ASTM D 4550
Standard Classification for Thermoplastic Elastomer-Ether-Ester (TEEE)
ASTM D 4551
Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Flexible
Concealed Water-Containment Membrane
ASTM D 4591
Standard Test Method for Determining Temperatures and Heats of Transitions
of Fluoropolymers by Differential Scanning Calorimetry
ASTM D 4603
Standard Test Method for Determining Inherent Viscosity of Poly(Ethylene
Terephthalate) (PET) by Glass Capillary Viscometer
ASTM D 4617
Standard Classification System for Phenolic Compounds (PF)
ASTM D 4634
Standard Specification for Styrene-Maleic Anhydride Materials (S/MA)
Standard Specification for Polyethylene Films Made from Low-Density
Polyethylene for General Use and Packaging Applications
Standard Test Methods for Polyurethane Raw Materials: Determination of
Specific Gravity of Isocyanates
Standard Test Methods for Polyurethane Raw Materials: Determination of the
Isomer Content of Toluenediisocyanate
Standard Test Methods for Polyurethane Raw Materials: Determination of Total
Chlorine in Isocyanates
Standard Test Methods for Polyurethane Raw Materials: Determination of Acid
and Alkalinity Numbers of Polyols
Standard Test Method for Polyurethane Raw Materials: Determination of
Hydrolyzable Chlorine of Isocyanates
ASTM D 4669
Standard Test Method for Polyurethane Raw Materials: Determination of
Specific Gravity of Polyols
Standard Test Method for Polyurethane Raw Materials: Determination of
Suspended Matter In Polyols
Standard Test Methods for Polyurethane Raw Materials: Determination of
Unsaturation of Polyols
A
Standard Test Methods for Polyurethane Raw Materials: Determination of Water
Content of Polyols
Back to Technical Home page